FUNAI DBVR-7510S
Skrócona Instrukcja Obsługi

QUICK SETUP GUIDE
Congratulations on your purchase of a FUNAI DVD/VCR. This Quick Setup Guide takes you through the first-time setup with simple instructions so you can enjoy exceptional audio and video quality as soon as possible. Please refer to the Owner's manual for detailed instructions. If you have read your instructions and still need assistance, call helpline at 0870-383-3010.

Clock Setting
Setting the Clock
This unit incorporates a 24-hour clock. The clock must be set for the Timer Recording function to operate correctly. 1) Press , then . 2) Press 3) Press or or to select �INITIAL�, then press to select �CLOCK�, then press . .
MENU TIMER SET UP INITIAL
STANDBY-ON SPEED/ SYSTEM
T-SET OPEN/CLOSE

1

2 5 8 0

3
CHANNEL

Unless stated, all procedures described use the remote control.
4) Use , or to select current year, month, date, hour and minutes. 5) Press to start the clock.

INITIAL CH TUNING CLOCK

4 7
CLEAR/ C.RESET

6 9 +10
DVD MODE

DISPLAY

VCR

Loading Batteries in the Remote Control

PLAY STOP

CLOCK YEAR MONTH DAY HOUR MINUTE

REC/OTR

SKIP SEARCH ENTER ZOOM

PAUSE AUDIO

2007 01 0 1 MO __ __

TOP MENU

MENU SETUP

RETURN

Note: � Press to go back to the item you want to correct during step 4). � Although seconds are not displayed, they begin counting from 00 when you exit by pressing . 1) Open the battery cover. 2) Insert two R6 (AA) batteries, with the (+) and (-) ends in the correct positions. 3) Close the cover. Use this feature to synchronize the clock with the correct time. � If the unit is unplugged or if there is a power failure for more than 30 seconds, you may have to reset the clock.

SUBTITLE

ANGLE

REPEAT

A-B

Connecting to a TV
VHF/UHF MIXER

Channel Presetting
WARNING!
Channel Presetting
Tuning of broadcast channels not already preset in the unit can be performed in two ways.

AERIAL

UHF

VHF

Never make or change connections with the power switched on. 1) Disconnect the antenna or cable from the

RF OUT

Automatic Channel Preset
MENU

STANDBY-ON SPEED/ SYSTEM

T-SET

OPEN/CLOSE

1) Turn on the TV and select the channel set as TV and connect it to the AERIAL jack of the
DVD
DIGITAL AUDIO OUT ANALOG AUDIO OUT S-VIDEO OUT

AERIAL

VHF/UHF MIXER

the video channel on the TV. unit. 2) Connect the RF OUT jack of the unit to the antenna in jack of the TV using the supplied RF cable. 3) Connect the AV1 (TV) scart jack of the unit to the scart input jack of the TV using a commercially available scart cable. 4) Plug in the TV and the unit. Note: � Playback picture from DVD and VCR cannot be delivered through the RF cable. The RF cable is only for sending the antenna signal to the TV. 2) Press 3) Press then press 4) Press or . . then press or 5) Press then press , then or . to select �CH TUNING� , to select �AUTO� , . to select �INITIAL� ,

TIMER SET UP INITIAL

1 4 7
CLEAR/ C.RESET

2 5 8 0
VCR

3 6 9 +10
DVD

CHANNEL

L
COAXIAL

VCR
DVD/VCR

AV2 (DECODER) AV1 (TV)

R

RF OUT

DISPLAY

MODE

INITIAL CH TUNING CLOCK
REC/OTR
TOP MENU

PLAY STOP
SKIP PAUSE

scart cable RF cable (not supplied) (supplied) to 21-pin scart jack
(TV)

SEARCH

AUDIO

MENU SETUP ZOOM

ENTER RETURN

CH TUNING AUTO MANUAL MOVE

SUBTITLE

ANGLE

REPEAT

A-B

to aerial jack

Scanning

PAL I_EN

1VMN23503 *****